Datalogic Scanning MAGELLAN 3200VSI Uživatelský manuál Strana 32
- Strana / 200
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
General Features
24
Magellan
TM
3200VSi
ERI Timeout
Specifies the amount of time the External Read Indicator (ERI) signal is held active for a good
read.
START / END
PROGRAMMING bar codes
Sets the ERI timeout duration using hex values from 000 to 255 in increments of ten milliseconds (10ms or 0.01 seconds). To config-
ure this feature, scan the “START/END” bar code above to place the unit in Programming Mode, then the “Set ERI Timeout,” followed
by the two digits (zero padded) from the Alphanumeric table in
Appendix C, Alpha-Numeric Pad representing the desired time
value. Exit programming mode by scanning the “START/END” bar code again.
DEFAULT SETTING FOR THIS FEATURE: 20 milliseconds (02)
Set ERI Timeout
- Magellan 1
- 3200VSi 1
- Product Reference Guide 1
- Table of Contents 3
- Product Reference Guide iii 5
- Product Reference Guide v 7
- Getting Started 9
- Connecting the Scanner 10
- Error Codes 11
- Mount Installation 12
- Wall Mount 13
- Countertop Mount 13
- LED and Beeper Indicators 14
- 7 15
- Programming 16
- Bar Code Mask 17
- Going Green 18
- General Features 19
- Composite label 21
- Scanner Button Options 22
- Camera Button Mode 23
- Auto Cell Phone Mode 24
- LED Level 25
- Auxiliary Port Mode 26
- Auxiliary Port Baud Rate 27
- Sleep Mode 29
- Sleep Mode — cont 30
- ERI Timeout 32
- Good Read: When to Indicate 33
- Good Read Beep Control 34
- Good Read Beep Frequency 34
- Good Read Beep Length 35
- Good Read Beep Volume 36
- Scanning Features 37
- Wake Up Intensity — cont 38
- Chapter 3 39
- Image Capture 39
- USB COM Interface 40
- Image Compression 41
- Image Format 41
- Image Size 42
- Image Brightness 43
- Image Contrast 43
- Interface Related Features 45
- Interface Selection 47
- Interface Selection — cont 48
- Obey/Ignore Host Commands 49
- Host Transmission Buffers 50
- RS-232 Interface Features 51
- Hardware Flow Control 53
- Intercharacter Delay 54
- Intercharacter Delay — cont 55
- Software Flow Control 55
- Host Echo 56
- Host Echo Quiet Interval 57
- Signal Voltage: Normal/TTL 58
- RS-232 Invert 59
- Beep on ASCII BEL 59
- Beep on Not on File 60
- ACK NAK Options 61
- ACK Character 62
- NAK Character 62
- Retry on ACK NAK Timeout 63
- ACK NAK Timeout Value 63
- ACK NAK Retry Count 64
- ACK NAK Error Handling 65
- Single Cable RS-232 66
- Single Cable RS-232 Use BCC 68
- Single Cable RS-232 Use STX 69
- Single Cable RS-232 Use ETX 70
- Single Cable Pacesetter Plus 71
- USB-OEM Device usage 72
- Keyboard Wedge 73
- USB Keyboard 73
- Keyboard Wedge — cont 74
- Caps Lock State 75
- USB COM Interface Set-up 79
- Data Editing 81
- Global Prefix/Suffix 82
- Global Prefix/Suffix — cont 83
- Label ID 85
- Label ID — cont 86
- Case Conversion 92
- Character Conversion 93
- UPC-A — continued 96
- Disable/Enable UPC-E 98
- UPC-E — continued 100
- Expand UPC/EAN to GTIN 101
- Disable/Enable EAN-13 102
- Check Digit Transmission 102
- EAN-13 — continued 103
- Disable/Enable EAN-8 104
- EAN-8 — continued 105
- EAN Two-Label 106
- Price Weight Check Digit 107
- Symbologies 108
- Add-ons — continued 109
- UCC/EAN 128 Emulation 110
- GS1-128 Emulation 111
- Length Control 112
- Coupon Read Control 114
- GS1 DataBar Limited 115
- Disable/Enable Code 39 116
- Check Character Calculation 116
- Check Character Transmit 117
- Start/Stop Characters 117
- Code 39 Full ASCII 118
- Code 39 — continued 119
- Code 32 Italian Pharmacode 121
- Code 128 123
- Code 128 — continued 124
- Interleaved 2 of 5 127
- Check Digit Transmit 128
- Disable/Enable Codabar 131
- Check Character Verification 131
- Codabar — continued 133
- Start/Stop Character Match 136
- Disable/Enable Code 93 137
- Code 93 — continued 138
- 2D Symbologies 141
- Disable/Enable PDF 417 142
- PDF 417 — continued 144
- Disable/Enable Micro PDF 417 145
- Micro PDF 417 — continued 147
- Disable/Enable Datamatrix 148
- Datamatrix — continued 150
- Disable/Enable QR Code 151
- QR Code — continued 153
- Maxicode 154
- Maxicode — continued 156
- Disable/Enable Aztec 157
- Aztec — continued 158
- Composite Labels 160
- Advanced Decoding Features 163
- Appendix A 165
- Product Specifications 165
- Physical Properties 166
- Electrical Parameters 166
- Environmental Parameters 166
- Other Parameters 166
- 159 167
- Appendix B 169
- Cable Pinouts 169
- Appendix C 171
- Alpha-Numeric Pad 171
- Appendix D 173
- Factory Default Settings 173
- Appendix E 179
- Appendix F 187
- Host Commands 187
- Appendix G 189
- Sample Symbols 189
- 1D Symbol Samples — continued 190
- 2D Sample Symbols 191
- Composite Sample Symbols 192
- Appendix H 193
- From Scanner to microSD Card 194
- 187 195
- By Autorun.dls file 195
- By scanning a label 195
- CPLD code load to the scanner 196
- 189 197
- By Autorun file 197
- ASCII Chart 199
Související produkty a manuály pro Čtečky čárových kódů Datalogic Scanning MAGELLAN 3200VSI
(65 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 1.009 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce