Datalogic Scanning DS1100 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Čtečky čárových kódů Datalogic Scanning DS1100. Datalogic Scanning DS1100 User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 8
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
DS1100 QUICK GUIDE
DS1100
General View: Laser Safety:
The scanner is classified as a Class 2 laser product according
to EN 60825-1 regulations and as a Class II laser product
according to CDRH regulations.
For installation, use and maintenance it is not necessary to
open the scanner.
There is a safety device which allows the laser to be switched
on only if the motor is rotating above the threshold for its correct
scanning speed.
The motor and the laser beam can be switched off through a
software command (see also the WinHost Help On Line).
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAX. OUTPUT RADIATION 1mW
EMITTED WAVE LENGTH 630-680 nm
TO EN 60825-1:2001
CAUTION-CLASS 3B LASER LIGHT WHEN
OPEN AVOID EXPOSURE TO BEAM
This product conforms to the
applicable requirements of
21CFR1040 at the date of
manufacture.
AVOID EXPOSURE
LASER LIGHT EMITTED
FROM THIS APERTURE
Figure A Warning and Device Class Label
1
2
3
4
8
7
6
5
Laser Beam Output Window
Laser Warning and
Device Class Label
Power On LED
Ext Trig LED
Laser On LED
Good Read LED
TX Data LED
Mounting Holes
The laser diode used in this device is classified as a class
3B laser product according to EN 60825-1 regulations
and as a Class IIIb laser product according to CDRH
regulations. As it is not possible to apply a classification
label on the laser diode used in this device, the following
label is reproduced below.
For further details on product installation,
see the complete Installation Manual.
DS1100 can be configured through the
WinHost Windows-based software program
available on the installation CD-ROM.
For configuration it is necessary to create a
cable connecting the scanner to the PC as
indicated in the “How To Build A Simple
Interface Test Cable” section of this guide.
Power Supply:
- This product is intended to be installed by
Qualified Personnel only.
- This accessory device is intended to be
supplied by a UL Listed or CSA Certified
Power Unit with «Class 2» or LPS power
source which supplies power directly to the
scanner via the 25-pin connector.
LASER LIGHT
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
MAX. OUTPUT RADIATION 7 mW
EMITTED WAVE LENGTH 630~680 nm
TO EN 60825-1 (2001)
Laser Diode Class Label
Any violation of the optic parts in particular can cause
radiation up to the maximum level of the laser diode
(7 mW at 630 to 680 nm).
WEEE Compliance:
1
8
3 4 5
7
6
2
Zobrazit stránku 0
1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - WEEE Compliance:

DS1100 QUICK GUIDE DS1100 General View: Laser Safety: The scanner is classified as a Class 2 laser product according to EN 60825-1 regulations and

Strany 2 - Accessories:

DS1100 QUICK GUIDE 2 Model Description: DS1100 - X X X X Optical Resolution 1 = Standard resolution2 = High resolution Communication Interface1

Strany 3 - Mechanical Installation:

DS1100 QUICK GUIDE 3 Electrical Connections: DS1100 is equipped with a cable terminated by a 25-pin female D-sub connector for connection with the

Strany 4 - Input/Output Connections:

DS1100 QUICK GUIDE 4 Reading Position: In DS1100-XXX1 models the laser beam is emitted from the output window with a 12° (± 2) skew angle. ± 2°L

Strany 5 - Connectivity:

DS1100 QUICK GUIDE 5 Connectivity: RS232 Point-to-point layout c RS232 Auxiliary Serial Interface d External Trigger (for On-Line mode) RS485

Strany 6 - Reading Diagrams:

DS1100 QUICK GUIDE 6 Reading Diagrams: DS1100-1XXX (Standard Resolution) CONDITIONS Code = Interleaved 2/5 or Code 39 PCS = 0.90 Pitch angle = 0°

Strany 7 - User Interface:

DS1100 QUICK GUIDE 7 User Interface: The following table contains the pinout for standard RS232 PC Host interface. For other user interface types p

Strany 8 - ENVIRONMENTS

DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy 05 dichiara che declares that the déclare que le bescheinigt, daß da

Komentáře k této Příručce

Žádné komentáře