Datalogic-scanning DS6400 Uživatelský manuál stáhnout pdf (Strana 110)

DS6400

5.2.2 Scanner Replacement Procedure

NOTE

The ASR procedure requires replacing one scanner at a time.

Slave

s).

3. Power up the system and wait for initialization.

Mas

he new Master.

4. Power up the system and wait for initialization.

1. Power down the entire system.

2. Replace the Slave scanner with a new one (default setting

ter

1. Load the saved configuration from file (.ddc) to t

2. Power down the entire system.

3. Replace the Master scanner with the new one.

NOTE

The ASR works only if both the Master and Slave devices have software

6.40 or later.

1 2 ... 105 106 107 108 109 110 111 112 113 114 115 ... 121 122

Reference Manual 1
CONTENTS 3
REFERENCES 6
COMPLIANCE 7
POWER SUPPLY 8
CE COMPLIANCE 8
WEEE COMPLIANCE 8
GENERAL VIEW 10
Laser Safety Label 11
Laser Beam Output Window 11
GUIDE TO INSTALLATION 13
1 INTRODUCTION 17
DS6400 - 10X - 0YY 18
INTRODUCTION 19
1.4 INDICATORS 21
1.5 ACCESSORIES 22
2 INSTALLATION 23
2.2 MECHANICAL MOUNTING 24
2.2.1 Mounting the Scanner 24
INSTALLATION 27
2.3 ELECTRICAL CONNECTIONS 29
(with INT-30 only) 30
Main Interface 32
RS232 Interface 32
RS485 Full-Duplex Interface 33
RS485 Half-Duplex Interface 34
Auxiliary Interface 35
EXTERNAL TRIGGER/ENCODER 36
Outputs 38
2.3.2 Lonworks Connectors 40
Network Termination 41
Lonworks Interface 42
2.3.3 Ethernet Connector 44
Figure 41 – Inverted Cable 45
25-pin male connector 48
2.6 TYPICAL INSTALLATIONS 51
2.6.1 Standard Installation 51
ATTENTION 52
2.7 TYPICAL LAYOUTS 52
2.7.1 Point-to-Point 52
Main Serial Interface 54
Fieldbus 56
2.7.5 Local Lonworks Network 58
Small Synchronized Network 59
Large Synchronized Network 61
2.7.6 Fieldbus Network 63
Network 63
2.8 FLASH™ DYNAMIC FOCUS 64
2.8.1 Fixed Mode 64
2.8.2 Continuous Mode 64
2.8.3 Triggered Mode 65
2.8.4 D-FLASH™ Mode 65
2.9 KEYPAD AND DISPLAY 66
2.9.1 Internal Net 66
2.9.2 Test Mode 67
3 SOFTWARE CONFIGURATION 68
SOFTWARE CONFIGURATION 69
On Line Operating Mode 70
Automatic Operating Mode 70
Net-Autoset 73
Express Network Setup 73
Network Wizard 74
3.4 PARAMETER DEFAULT VALUES 77
4 READING FEATURES 81
Conveyor 82
Laser Beam 82
SPY ICON 84
Position 1 85
Position 2 85
Position 3 85
4.3 PERFORMANCE 86
4.3.1 Reading Conditions 86
4.4 READING DIAGRAMS 88
4.4.1 DS6400 Standard Model 89
Position = 90 cm 91
Position = 60 cm 99
Min. Reading 100
Distance 100
Max. Reading 100
Global Reading 101
Position = 95 cm 101
READING FEATURES 105
MAINTENANCE 109
TROUBLESHOOTING 111
7 TECHNICAL FEATURES 114
TECHNICAL FEATURES 115
GLOSSARY 116
Parameter Groups 120
Default Values; 61 120
DECLARATION OF CONFORMITY 121

Komentáře k této Příručce

Žádné komentáře

Datalogic-scanning DS6400 Uživatelský manuál Strana 110

Komentáře k této Příručce

Související produkty a manuály pro Skenery Datalogic-scanning DS6400